2条回答
- a2091244734 2015-09-05 15:12关注
要在三层交换机启用ip routing,把不同的终端放到不通的vlan里面,把vlan业务做到三层交换机上,我这边有个案列,你可以看看
三层交换机与路由器的配置 实例(图解)目的:学会使用三层交换与路由器让处于不同网段的网络相互通信
实验步骤:一:二层交换机的配置:
在三个二层交换机上分别划出两VLAN,并将二层交换机上与三层交换或路由器上的接线设置为trunk接口
二:三层交换机的配置:
1:首先在三层交换上划出两个VLAN,并进入VLAN为其配置IP,此IP将作为与他相连PC的网关。
2:将与二层交换机相连的线同样设置为trunk接线,并将三层交换与路由器连接的线设置为路由接口(no switchsport)
3:将路由器和下面的交换机进行单臂路由的配置
实验最终结果:拓扑图下各个PC均能相互通信
c
交换机的配置命令:
SW 0:
Switch>
Switch>en
Switch#conf
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vlan 2
Switch(config-vlan)#exit
Switch(config)#int f0/2
Switch(config-if)#switchport access vlan 2
Switch(config-if)#no shut
Switch(config-if)#int f0/3
Switch(config-if)#switchport mode trunk
Switch(config-if)#switchport mode trunk
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up
Switch(config-if)#exit
Switch(config)#
SW 1:
Switch>en
Switch#conf
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int f0/2
Switch(config-if)#switchport access vlan 2
% Access VLAN does not exist. Creating vlan 2
Switch(config-if)#no shut
Switch(config-if)#exit
Switch(config)#int f0/3
Switch(config-if)#switchport mode trunk
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up
Switch(config-if)#
SW 2:
Switch>en
Switch#conf
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int f0/2
Switch(config-if)#switchport access vlan 2
% Access VLAN does not exist. Creating vlan 2
Switch(config-if)#exit
Switch(config)#int f0/3
Switch(config-if)#switchport mode trunk
Switch(config-if)#
三层交换的配置命令:
Switch>en
Switch#conf
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int f0/1
Switch(config-if)#switchport mode trunk
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
Switch(config-if)#exit
Switch(config)#int f0/2
Switch(config-if)#switchport mode trunk
Switch(config-if)#exit
Switch(config)#vlan 2
Switch(config-vlan)#exit
Switch(config)#int vlan 1
Switch(config-if)#no shut
%LINK-5-CHANGED: Interface Vlan1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Switch(config-if)#ip address 192.168.1.168 255.255.255.0
Switch(config-if)#exit
Switch(config)#int vlan 2
%LINK-5-CHANGED: Interface Vlan2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to upSwitch(config-if)#ip add
Switch(config-if)#ip address 192.168.2.168 255.255.255.0
Switch(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/3, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up
Switch(config-if)#exit
Switch(config)#int f0/3
Switch(config-if)#no switchport
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to upSwitch(config-if)#
Switch(config-if)#ip address 192.168.10.1 255.255.255.0
Switch(config-if)#no shut
Switch(config-if)#exit
Switch(config)#ip routing
Switch(config-if)#exit
Switch(config)#ip route 0.0.0.0 0.0.0.0 192.168.10.2
Switch(config)#
路由器的配置:
Router>en
Router#conf
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int f0/1
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Router(config-if)#exit
Router(config)#int f0/0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int f0/0.1
Router(config-subif)#encapsulation dot1Q 1
Router(config-subif)#ip address 192.168.3.168 255.255.255.0
Router(config-subif)#exit
Router(config)#int f0/0.2
Router(config-subif)#encapsulation dot1Q 2
Router(config-subif)#ip add
Router(config-subif)#ip address 192.168.4.168 255.255.255.0
Router(config-subif)#exit
Router(config)#ip route 0.0.0.0 0.0.0.0 192.168.10.1
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Router#conf
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int f0/1
Router(config-if)#ip add
Router(config-if)#ip address 192.168.10.2 255.255.255.0
Router(config-if)#解决 无用评论 打赏 举报
悬赏问题
- ¥15 (希望可以解决问题)ma和mb文件无法正常打开,打开后是空白,但是有正常内存占用,但可以在打开Maya应用程序后打开场景ma和mb格式。
- ¥20 ML307A在使用AT命令连接EMQX平台的MQTT时被拒绝
- ¥20 腾讯企业邮箱邮件可以恢复么
- ¥15 有人知道怎么将自己的迁移策略布到edgecloudsim上使用吗?
- ¥15 错误 LNK2001 无法解析的外部符号
- ¥50 安装pyaudiokits失败
- ¥15 计组这些题应该咋做呀
- ¥60 更换迈创SOL6M4AE卡的时候,驱动要重新装才能使用,怎么解决?
- ¥15 让node服务器有自动加载文件的功能
- ¥15 jmeter脚本回放有的是对的有的是错的