有没有人能告诉我一下，我这个mcnp5程序输出后文件为什么没有tally项啊？
1- Coxial HPGe detector
2- c Detector
3- 101 2 -2.7 (113 -112 -133):(112 -103 132 -133):(103 -101 134 -133) $
4- 102 1 -0.001293 (102 -101 -134) $
5- 103 3 -1.8 (103 -102 -134) $
6- 104 2 -2.7 (111 -104 -131) #(110 -105 -130) #(111 -110 -121) $
7- 105 4 -8.9 (112 -114 -135) $
8- 111 10 -5.3255 (107 -106 -123) #(107 -108 -122) $
9- 112 10 -5.3255 (107 -109 121 -122):(109 -108 -122) $
10- 113 10 -5.3255 (107 -106 123 -124):(106 -105 -124) $
11- 199 1 -0.000001 (113 -101 -133)
12- #101 #102 #103 #104 #105 #111 #112 #113 $
13- 200 1 -0.001293 -999 #(113 -101 -133) $
14- 999 0 999 $
15-
16- c Outer World
17- 999 so 1000
18- c Detector
19- 101 px -20.0 $ Al
20- 102 px -20.04 $ Carbon:1.6mm Carbon Fiber
21- 103 px -20.2 $ Al Carbon
22- 104 px -20.6 $ Space:4mm Space
23- 105 px -20.6003 $ Al/Mylar:0.03mm/0.03mm Al/Mylar
24- 106 px -20.60033 $ Dead Layer: 0.3micron Ge/B Dead Layer
25- 107 px -29.0 $ HPGe Length 84mm : 20.6+8.4=29.0
26- 108 px -21.43 $ Inner Dead Layer:700 micron Ge/Li Dead Layer
27- 109 px -21.5 $ Hole Depth 75mm : 29.0-7.5=21.5
28- 110 px -33.3 $ Space: 3mm Tray
29- 111 px -33.6 $ Al:130mm Cup Length
30- 112 px -34.5 $ Al Shell End
31- 113 px -35.0 $ Al Shell End
32- 114 px -21.83 $ Cu Contact Pine End
33- 121 cx 0.445 $ Hole Diameter 8.9mm
34- 122 cx 0.515 $ Inner Dead Layer:700 micron Ge/Li Dead Layer
35- 123 cx 3.37497 $ Outer Dead Layer: 0.3micron Ge/B Dead Layer
36- 124 cx 3.375 $ HPGe Diameter 67.5mm
37- 130 cx 3.82 $ Al Cup
38- 131 cx 3.90 $ Al Cup：0.8mm Al
39- 132 cx 4.60 $ Al Shell: 1.5mm Al
40- 133 cx 4.75 $ Al Shell: GMX70P4-95-CW:Diameter 95mm
41- 134 cx 3.90 $ Al & Carbon
42- 135 cx 0.18 $ Cu Contact Pine in HPGe Hole
43-
44- imp:p,e 1 9r 0
45- mode p e
46- sdef pos 0 0 0 erg 0.2446974 par 2
47- m1 7014 -0.7571 8016 -0.2305 18000 -0.0124 $ Air
48- m2 13027 1 $ Al
49- m3 6012 -0.9893 6013 -0.0107 $ Carbon
50- m4 29063 -0.6917 29065 -0.3083 $ Cu
51- m10 32070 -20.37 32072 -27.31 32073 -7.76 32074 -36.73 32076 -7.83 $ Ge
52- f18:p,e 111
53- e18 0 9999i 2
54- f28:p,e 111
55- e28 0 9999i 2
56- ft28 geb 0.00122 0.000746312 0.0884
57- nps 1e7
58- c ctme 120
59-
surface 131 and surface 134 are the same. 134 will be deleted.
comment. 1 surfaces were deleted for being the same as others.
warning. 1 materials had unnormalized fractions. print table 40.
warning. 1 of the materials appear at more than one density.
1cells print table 60
atom gram photon electron
cell mat density density volume mass pieces importance importance
1 101 2 6.02616E-02 2.70000E+00 1.03068E+02 2.78283E+02 1 1.0000E+00 1.0000E+00
2 102 1 5.35617E-05 1.29300E-03 1.91134E+00 2.47137E-03 1 1.0000E+00 1.0000E+00
3 103 3 9.02561E-02 1.80000E+00 7.64538E+00 1.37617E+01 1 1.0000E+00 1.0000E+00
4 104 2 6.02616E-02 2.70000E+00 3.88034E+01 1.04769E+02 1 1.0000E+00 1.0000E+00
5 105 4 8.43604E-02 8.90000E+00 1.28965E+00 1.14779E+01 1 1.0000E+00 1.0000E+00
6 111 10 4.41756E-02 5.32550E+00 2.94267E+02 1.56712E+03 1 1.0000E+00 1.0000E+00
7 112 10 4.41756E-02 5.32550E+00 1.64169E+00 8.74281E+00 1 1.0000E+00 1.0000E+00
8 113 10 4.41756E-02 5.32550E+00 6.41716E-03 3.41746E-02 1 1.0000E+00 1.0000E+00
9 199 1 4.14244E-08 1.00000E-06 6.14600E+02 6.14600E-04 1 1.0000E+00 1.0000E+00
10 200 1 5.35617E-05 1.29300E-03 4.18879E+09 5.41610E+06 1 1.0000E+00 1.0000E+00
11 999 0 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0 0.0000E+00 0.0000E+00
total 4.18879E+09 5.41809E+06
minimum source weight = 1.0000E+00 maximum source weight = 1.0000E+00
***************************************************
* Random Number Generator = 1 *
* Random Number Seed = 19073486328125 *
* Random Number Multiplier = 19073486328125 *
* Random Number Adder = 0 *
* Random Number Bits Used = 48 *
* Random Number Stride = 152917 *
***************************************************
2 warning messages so far.
1cross-section tables print table 100
table length
bad trouble in subroutine ffetch of xact
CFS fetching no longer possible
